[Timezone Detection]
Create Account - Join in Seconds!

User Name: Email Address:
Human Verification

Please enter the six letters or digits that appear in the image opposite.

How do builld a standpipe for your Internal Overflow


Bookmark and Share
Page 1 of 4 1 2 3 ... Last
Results 1 to 10 of 31
  1. #1
    seahorsedreams - Reefkeeper Registered User
    Join Date
    Aug 2005
    Location
    Palos Verdes, California
    Posts
    482

    Default How do builld a standpipe for your Internal Overflow

    These things are supposed to make your tank QUIET! This set-up is for a 1" Bulkhead so the pipe 1-1/4" as well as most of the fitting unless otherwise indicated.

    PVC pieces needed for the actual stand pipe..... ALL fittings are to be SLIP fittings! (not threaded... just in case someone didn't know what I meant by slip).
    1. 1-1/4" PVC End Cap
    2. 1-1/4" PVC Street-Ell
    3. 1-1/4" PVC Tee
    4. 1-1/4" PVC Pipe (the amount I got was the height of my tank + another foot to make connectors)
    5. 1-1/4" PVC Coupling
    6. 1-1/4 to 1" Reducer Bushing
    7. 1" PVC Pipe (a small piece... say half a foot)
    8. 1" Bulkhead (slip fitting)

    1 - How do builld a standpipe for your Internal Overflow
    ______________________________________

    Renee

  2. #2
    seahorsedreams - Reefkeeper Registered User
    Join Date
    Aug 2005
    Location
    Palos Verdes, California
    Posts
    482

    Default

    Other materials Needed:
    1. Teflon Tape
    2. PVC Cement
    3. 1 AirlineValve
    4. 3/16 Rigid Airline Tubing (1 inch piece)
    5. Flexible Airline Tubing (about 6")
    6. Acetone (OPTIONAL: see below)

    Optional PVC Fittings and other materials if using the 1" Strainer modification.
    (9) 1" Intake Strainer
    (10) 1-1/4 to 1" Reducer Bushing (same part as above... you'll just need two)
    (11) 1" PVC End Cap
    (12) Silicone Glue 1" PVC End Cap

    2 - How do builld a standpipe for your Internal Overflow
    ______________________________________

    Renee

  3. #3
    seahorsedreams - Reefkeeper Registered User
    Join Date
    Aug 2005
    Location
    Palos Verdes, California
    Posts
    482

    Default

    Equipment needed.
    (1) Dremel or a Drill with 3/16 drill bit (you need to drill a 3/16 hole in the end cap. So, the drill is easier
    but a dremel will do if you are careful. BUT: if you decide to go with the "Strainer Modification"
    you will need the Dremel to grind down the inside of the End cap and the Reducer Bushing.
    (2) Pipe Cutter: This can be done using....
    ... PVC Pipe Cutter (this is what I used)
    ... Tubing Cutter (be careful to get one that can handle the 1-1/4" tubing... and they can run kind of
    expensive at that diameter.
    ... Plain ole Jig Saw (But OMG the mess!!! I tried this method one time and I never thought I
    would be free of the PVC dust ever again! ... But it works.... it's just messy.


    3 - How do builld a standpipe for your Internal Overflow
    ______________________________________

    Renee

  4. #4
    seahorsedreams - Reefkeeper Registered User
    Join Date
    Aug 2005
    Location
    Palos Verdes, California
    Posts
    482

    Default

    Okay... so now we have everything... we just need to build it.... the fun part!

    First of all I'm sure some have noticed that the print on the side of the PVC pipe is just ugly. Those of you who haven't noticed it, don't worry about it and skip this part. For those of you that it bugs this is where the optional acetone comes in. And what's so good about Acetone? See the pic below.

    4 - How do builld a standpipe for your Internal Overflow
    ______________________________________

    Renee

  5. #5
    seahorsedreams - Reefkeeper Registered User
    Join Date
    Aug 2005
    Location
    Palos Verdes, California
    Posts
    482

    Default

    Ahhhhhh! Nice and clean.....

    Now let's get started on construction.
    A pic says a thousand words in my opinion (Guess it doesn't surprise you that I would say that). Below I've laid out all the parts of the main part of the standpipe that simply have to be connected by one way or another to form the main body.

    5 - How do builld a standpipe for your Internal Overflow
    ______________________________________

    Renee

  6. #6
    seahorsedreams - Reefkeeper Registered User
    Join Date
    Aug 2005
    Location
    Palos Verdes, California
    Posts
    482

    Default

    Before we start gluing things together we need to figure out how high this needs to be. Tap the pieces 1 through 7 together. It is best if you place teflon on the connectors to make sure you can dismantle them after. For me the height was very important because it would be fitting under the ledge of the tank. If yours is totally in the open, then it's not too important. And also note not to cut the main PVC pipe thinking this will be the end height when it is only temporarily placed together. When you actually pound the connectors together, it will make the whole standpipe shorter. But remember, you do not want to pound it too well before you are ready to make a permanent connection because you may never get it apart again.

    We also need to prepare the end cap (otherwise known as #1 in the above photo).

    This is where if you have a drill with a 3/16 drill bit the job is very fast and precise. It can definitely be done with a dremel, it just takes a little more care while at the risk of not having the same precision.

    6 - How do builld a standpipe for your Internal Overflow
    ______________________________________

    Renee

  7. #7
    seahorsedreams - Reefkeeper Registered User
    Join Date
    Aug 2005
    Location
    Palos Verdes, California
    Posts
    482

    Default

    The hole is drilled to accommodate a piece of rigid airline tubing. There are many different ways to accomplish the purpose of this part which we will talk about later.

    7 - How do builld a standpipe for your Internal Overflow
    ______________________________________

    Renee

  8. #8
    seahorsedreams - Reefkeeper Registered User
    Join Date
    Aug 2005
    Location
    Palos Verdes, California
    Posts
    482

    Default

    Then to the end of the rigid tubing you place the airline tubing and then the air valve regulator. Make the tubing long enough so that you can reach it in the future to adjust the valve. Just don't make it any longer than necessary because the longer it is the more the air flow will be restricted and may necessitate a second hole. (The flexible tubing in the pic is dirty so you can see it better )

    8 - How do builld a standpipe for your Internal Overflow
    ______________________________________

    Renee

  9. #9
    seahorsedreams - Reefkeeper Registered User
    Join Date
    Aug 2005
    Location
    Palos Verdes, California
    Posts
    482

    Default

    Okay, so you got the height figured out, the cap drilled, now let's glue or teflon the connections together. The whole thing is not just glued with PVC Cement... there are some parts you'll want to be removable so you just make those connections snug with teflon tape. The pic below should clearly illustrate which connections are glued and which are tefloned (is that a word ). I used a rubber mallet to tap the cemented connections.

    9 - How do builld a standpipe for your Internal Overflow
    ______________________________________

    Renee

  10. #10
    seahorsedreams - Reefkeeper Registered User
    Join Date
    Aug 2005
    Location
    Palos Verdes, California
    Posts
    482

    Default

    All the connections made and sealed!! :D

    10 - How do builld a standpipe for your Internal Overflow
    ______________________________________

    Renee

Page 1 of 4 1 2 3 ... Last

Similar Topics

  1. Diseases & Treatment Internal Parasite?
    By MizTanks in forum Marine Fish
    Replies: 7
    Last Post: 08-02-2012, 03:42 AM
  2. Flow & Plumbing best internal return pump
    By demonclownfish in forum Hardware
    Replies: 22
    Last Post: 03-02-2011, 03:53 PM
  3. Standpipe Buoy??
    By dkode in forum Basics
    Replies: 7
    Last Post: 12-13-2006, 05:50 PM
  4. Seahorses & Pipefish Internal parasites ..Sea Horse
    By Sea~Horse~Whisperer in forum Marine Fish
    Replies: 0
    Last Post: 04-13-2006, 12:55 AM
  5. Internal parasites ..Sea Horse
    By Sea~Horse~Whisperer in forum Basics
    Replies: 0
    Last Post: 04-13-2006, 12:55 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

About CaptiveReefs

    If you are interested in learning about reefkeeping or have a problem with your reef, our reefkeeping community is here to help. Feel free to ask a question or search our site. We have lots of experienced reefkeepers that are willing to provide free reefkeeping advice!

    Besides being a great resource for all levels of reef aquarium hobbyists, CaptiveReefs is a social experience that will enhance your enjoyment of reefkeeping. CaptiveReefs is committed to connecting reefkeepers with the support and information they need to grow beautiful coral reef aquariums.

Information

Connect with Us